Journal of Clinical and Diagnostic Research, ISSN - 0973 - 709X

Users Online : 5543

Original article / research
Year : 2017 | Month : April | Volume : 11 | Issue : 4 | Page : ZC128 - ZC135

A Comparative Evaluation of Accuracy of the Dies Affected by Tray Type, Material Viscosity, and Pouring Sequence of Dual and Single Arch Impressions- An In vitro Study

Poonam R. kulkarni, Rahul S. kulkarni, Rupal J. Shah, Rahul Chhajlani, Bhuwan Saklecha, Kavita Maru

1. Senior Lecturer, Department of Prosthodontics, Sri Aurobindo College of Dentistry and PG Institute, Indore, Madhya Pradesh, India. 2. Senior Lecturer, Department of Prosthodontics, Index Institute of Dental Sciences, Index City, Indore, Madhya Pradesh, India. 3. Professor and Head, Department of Prosthodontics, Government Dental College, Ahmedabad, Gujarat, India. 4. Senior Lecturer, Department of Oral and Maxillofacial Surgery, Index Institute of Dental Sciences, Index City, Indore, Madhya Pradesh, India. 5. Reader, Department of Orthodontics, Index Institute of Dental Sciences, Index City, Indore, Madhya Pradesh, India. 6. Professor, Department of Prosthodontics, Sri Aurobindo College of Dentistry and PG Institute, Indore, Madhya Pradesh, India.

Correspondence Address :
Dr. Poonam R. Kulkarni,
8A, Krishi Vihar Colony, Near Tilak Nagar, Indore, Madhya Pradesh, India.
E-mail: poonamrahulkulkarni@gmail.com

Abstract

Introduction: The clinician’s skill, impression techniques, and materials play a very important role in recording fine details in an impression for accuracy of fixed partial denture prosthesis. Impression of prepared teeth and of the opposing arch can be recorded simultaneously by dual-arch trays, while the full arch metal trays are used for impressions of prepared teeth in one arch.

Aim: To measure and compare the accuracy of working dies made from impressions with metal and plastic dual arch trays and metal full arch trays, for two viscosities of impression material and by changing the sequence of pour of working and non-working sides.

Materials and Methods: A balanced design with independent samples was used to study the three variables (tray type, impression material viscosity, and pouring sequence). An impression made by dual arch trays and single arch trays were divided in to three groups (Group A-plastic dual arch tray, Group B-metal dual arch tray, Group C-full arch metal stock tray). Out of these three groups, two groups (Group A and B) were subdivided in to four subgroups each and one group (Group C) was subdivided in to two subgroups. A sample size of 30 was used in each subgroup yielding a total 300 impressions in three groups or ten subgroups. Impressions were made of a machined circular stainless steel die. All three dimensions (Occlusogingival, Mesiodistal, and Buccolingual) of the working dies as well as stainless steel standard die were measured three times, and the mean was used for the three standard sample values to which all working dies means were compared. Statistical analysis used for this study was a 3-factor analysis of variance with hypothesis testing at a =0.05.

Results: With respect to the selection of impression material viscosity statistically significant differences were found in the dies for the buccolingual and mesiodistal dimensions. Metal dual arch trays were slightly more accurate in the mesiodistal dimension in comparison to the plastic trays in reference of tray selection and in view of pouring sequence no differences were observed in occlusogingival dimension but in buccolingual and mesiodistal dimensions nonworking side was more accurate.

Conclusion: The gypsum dies produced from the dual arch impressions were generally smaller in all three dimensions than the stainless steel standard die. Plastic dual-arch trays were more accurate with rigid impression material and there was not statistically significant difference for sequence of pouring. Metal dual-arch trays were more accurate with monophase impression material and working side was more accurate. Stock metal full arch trays were more accurate for monophase impression material.

Keywords

Metal and plastic dual arch trays, Stainless steel standard crown, Stock metal full arch trays

How to cite this article :

Poonam R. kulkarni, Rahul S. kulkarni, Rupal J. Shah, Rahul Chhajlani, Bhuwan Saklecha, Kavita Maru. A COMPARATIVE EVALUATION OF ACCURACY OF THE DIES AFFECTED BY TRAY TYPE, MATERIAL VISCOSITY, AND POURING SEQUENCE OF DUAL AND SINGLE ARCH IMPRESSIONS- AN IN VITRO STUDY. Journal of Clinical and Diagnostic Research [serial online] 2017 April [cited: 2017 May 27 ]; 11:ZC128-ZC135. Available from
http://jcdr.net/back_issues.asp?issn=0973-709x&year=2017&month=April&volume=11&issue=4&page=ZC128-ZC135&id=9756

DOI and Others

DOI: 10.7860/JCDR/2017/24292.9756


Date of Submission: Sep 20, 2016
Date of Peer Review: Nov 29, 2016
Date of Acceptance: Feb 05, 2017
Date of Publishing: Apr 01, 2017

Financial OR OTHER COMPETING INTERESTS: None.

JCDR is now Monthly and more widely Indexed .
  • PubMed Central® (PMC)New
  • Academic Search Complete Database
  • Chemical Abstracts Service
  • Directory of Open Access Journals (DOAJ)
  • EBSCOhostNew
  • Embase & EMbiology
  • Google Scholar
  • HINARI Access to Research in Health Programme
  • Indian Science Abstracts (ISA)
  • Journal seek Database
  • Open J-Gate
  • Popline (reproductive health literature)
  • SCOPUS
  • www.omnimedicalsearch.com